Looking for:
Honeywell lynx touch l5000 manual - |
Honeywell lynx touch l5000 manual
The system displays the Keypad screen. The system returns to the Users screen. User Code 8. The maximum message duration is seconds. When you are finished listening to the message, you may Message 2 PM September 5, You may still program the correct Time Zone as shown below.
Check with your installer to see if your system is equipped with a Communications Module. The system advances to the next screen OR proceed to step Check with your installer to see if this option is available. Up to 40 rules can be programmed. The system displays a keypad. Ready To Arm 5. None 6. At the Schedules screen, select the Schedule you wish to edit. The Schedule programming screen will appear. At the Rules Programming Screen, select the Rule that you wish to edit or delete.
Check with your installer to see if the latter feature has been programmed on your control. Programming a Reminder Ready To Arm 1. Name Frequency None 6. At the Reminders screen, select the reminder you wish to edit. Walk Dog - Daily 2. The Reminder programming screen will appear. Follow the steps as noted above in the programming a Reminder section to edit and save your changes.
The system displays the WiFi options screen. Check with your installer to see if this features is available. The system is defaulted to automatically recover within approximately 1 minute after communication has been restored. Only those controls that are applicable to the specific camera will be displayed. The system will provide the appropriate voice messages and any system beeping sounds indicating the status of the security system over the phone line.
The feature allows images to be displayed on the touch screen when it is not in use. Connection to Total Connect Service is required in order for your installer to upload images to your panel. The Walk Test mode allows each protection point to be checked for proper operation. When the Walk Test mode is active, the control sounds a single beep every 30 seconds as a reminder that the system is in the Test mode.
If Walk Test is selected proceed to Step 5. If Prod. XX Dialer Test is selected proceed to Step 6. To make sure that your system is in working condition, do the following: 1.
Alkaline batteries provide a minimum of 1 year of operation, and in most units and applications, provide 2—4 years of service. Actual battery life will depend on the environment in which the sensor is used, the number of signals that the transmitter in the sensor has had to send, and the specific type of sensor.
General Your fire alarm system if installed is active 24 hours a day, providing continuous protection. With regard to the number and placement of smoke and heat detectors, we subscribe to the recommendations contained in the National Fire Protection Association's NFPA Standard 72 noted below. Establish and regularly practice a plan of escape in the event of fire. The following steps are recommended by the National Fire Protection Association: 1. Unauthorized changes or modifications could void the user's authority to operate the equipment.
Arranging some kind of regular service program with him is advisable. Your local Honeywell dealer is: Name: Address: Phone: — 76 — Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a variety of reasons. We recommend that your certified installer demonstrate disconnecting the phones on installation of the system. Page 86 Ready indicator See your installer for the function s that may have been programmed for your system.
When activated, three beeps will sound at the control whenever a protected perimeter door is opened and the zone voice descriptor will be announced. These secondary users are identified by "User Numbers" when their codes are assigned. You can assign up to 14 user codes.
Enter your 4-digit Master User Code. The Program the system system displays Master User programming screen. The system displays the Master User screen. The system returns to Enter Code the Users screen and the new User is displayed.
Clear Done V The system displays the Users screen. The maximum message duration is seconds. The system displays the recorded Message 1 PM September 1, messages. To record additional messages if recording Message 2 PM September 5, Ready To Arm 1. You may still program the correct Time Zone as shown below. June 5. The system displays a calendar. Select the correct month. January February Up to 16 devices can be programmed. The system displays the Devices screen.
The system displays the scheduling options screen. The system displays a keypad. Check with your installer to see if the latter feature has been programmed on your control. The system displays the Reminder programming screen. No items to display! Enter a name for the scheduled function on the displayed keypad Name Frequency This allows the user to disarm the system or take other appropriate actions in the security mode without interrupting the telephone session.
The system displays the Keypad screen. Zones System Arm Away The system will provide the appropriate voice messages and any system beeping sounds indicating the status of the security system over the phone line. To remotely disarm system Should you become aware of a fire emergency before your detectors sense the problem, go to the LYNX Touch and press and hold the panic key and then select the Fire icon.
The alarm will sound and an alarm will be transmitted to the central station. With regard to the number and placement of smoke and heat detectors, we subscribe to the recommendations contained in the National Fire Protection Association's NFPA Standard 72 noted below. Establish and regularly practice a plan of escape in the event of fire.
The following steps are recommended by the National Fire Protection Association: 1. When the Walk Test mode is active, the control sounds a single beep every 30 seconds as a reminder that the system is in the Test mode.
Page 64 Test mode will remain active until exited via an Off sequence. To make sure that your system is in working condition, do the following: 1.
Test your system weekly. Unauthorized changes or modifications could void the user's authority to operate the equipment. Page 71 5. We recommend that your certified installer demonstrate disconnecting the phones on installation of the system.
Arranging some kind of regular service program with him is advisable.
No comments:
Post a Comment